It takes several turns before the trimmer will start, because the drill (even fully charged) doesn't really turn it as fast as it probably needs to. Videos you watch may be.
Most engines have a key in the shaft to catch the starter , then the taper pushes it off.
How to start a weed eater with a drill. Causes of a stalling weed eater. Get it as soon as fri, aug 20. Finally, when you want to start your weed eater, you must show high care and hold the weed eater on those to specific parts of the structure.
Invest in a better stroke oil. How to jump start a weed wacker! Lay the weed eater flat on the ground, rip the cord, and you can begin your yard work.
3.3 out of 5 stars. Then press the purge valve 5 to 6 times to push fresh gas into the carburetor. Remove from the weed eater the fuel tank cap and reserve it.
A problem with some or a combination of these parts could cause the weed eater to cut off after turning it on. You will learn the basic safety procedures, the primary steps to starting your stihl trimmer and the importance of checking the choke. I use his adapter and a 3/8 inch, 18v drill to start my trimmer.
The symbol for the on position is | whereas the off position symbol is o. push the rubber primer bulb eight times. Below is a list of issues that could cause an engine to stall: You can feel much safer when you use kind of a best battery weed eater.
Place the trimmer on a flat, bare surface such as a sidewalk or driveway. It's not a problem, and it definitely works, but a larger, more powerful drill might start the motor just a. Excess gas sitting in the line and in carb over the winter causes blockage, so always empty and clean when not in use for extended periods.
Hold the throttle trigger on the handle, press both levers, and push the starter to the “i”, or start, position. Rather than buy a new recoil for the old mower, i took the top cover off, to mark where the flywheel nut was located. Then, press the purge valve 5.
How to start a weed eater with a choke. Press the ignition switch to the on position. After that, hold the weed eater to the ground with your hand to brace it.
Make sure the trimmer is laying on the ground and the opposite side of the starter grip handle is the one in contact with the surface. To make sure your weed eater lasts that long. First, you must remove the filler cap and fill the tank with a 50:1 gas to oil ratio fuel.
How to jump start a weed wacker! Find a place to start: Simply add the drill bit to your power drill and plug the bit into your electric start capable handheld equipment for easy starting.
I drilled a 1 hole in the plastic cover and used a drill and socket to start the mower. Brace the weed eater by holding it to the ground with one hand. This is an important step on how to start a stihl weed eater.
I had to make several ends for the drill for the different shaft sizes. If you don't have a key you can put a pin through the shaft. About 7 1/2 minutes into the video you see his starter.
In this video, stihl demonstrates how to properly and safely start your stihl trimmer. Also make sure the trimmer line is not touching any object or the ground. Once the kill switch is engaged, find the choke and switch it to the “on” or “closed” position, which will allow you to cold start your weed whacker.
Store the weed eater safely. If the engine doesn’t start after you pull the rope for 9 to 10 times, stop for a few seconds, squeeze the throttle trigger, then try again. Electric start drill bit engine starter eliminates manual pull starts with the push of a button.
Press primer bulb a few times forcing excess gas in line to run into carb, and then pull starter rope a few times forcing all the gas out. To start a gas powered weed whacker, start by placing it on the ground and flipping the kill switch on. (dirtslingers) if playback doesn't begin shortly, try restarting your device.
Free shipping on orders over $25 shipped by amazon. One hand, usually the right one, sticks to the upper part of the weed eater, at the clutch button and your left hand, at the circle part, in the middle of the weed eater. I used the drill and socket for 6 years, until i hit a rock and bent the crankshaft.
How to start use a stihl fs 46 weedeater weed grass trimmer wacker 45 55 ang gru. Drill bit attaches to most cordless drills with a. I ultimately decided to create.
Weed eater won t start: I’m always looking for optimization, so one time i was wondering how a drill could be used to enhance tedious chores. Depress the fuel bulb until it is filled with fuel.
Use your other hand to pull the starter rope as fast as possible until the engine starts. If your trimmer has a priming bulb, which is a small, clear plastic button attached to the trimmer housing over the carburetor, you have to press this several times before pulling the starting cord. Make sure the socket will come off easily or when the weedeater starts it will turn faster than the drill and may hurt you.
Must watch how to start any string trimmer |weed eater| with a drill. The engine of a weed eater is made up of several parts. Just take the recoil off and get the right size socket.
Be sure to safely start your ryobi string trimmer to prevent injuries and damage to you or the machine. 4 pieces engine drill bit adapter engine starter adapter electric start drill bit adapter with 4 storage bag for trimmer, leaf blower, garden cultivator, handheld equipment. Place the weed eater in a safe place.